Struct Status

pub struct Status {
    bits: u16,
}

PCI device common config space status register.

Fields

bits: u16

Implementations

impl Status

pub const INTERRUPT_STATUS: Self

The status of the device’s INTx# signal.

pub const CAPABILITIES_LIST: Self

Sets to 1 if the device support capabilities.

pub const MHZ66_CAPABLE: Self

Sets to 1 if the device is capable of running at 66 MHz.

pub const FAST_BACK_TO_BACK_CAPABLE: Self

Sets to 1 if the device can accept fast back-to-back transactions that are not from the same agent.

pub const MASTER_DATA_PARITY_ERROR: Self

This bit is only set when the following conditions are met:

1. The bus agent asserted PERR# on a read or observed an assertion of PERR# on a write
2. The agent setting the bit acted as the bus master for the operation in which the error occurred
3. Bit 6 of the Command register (Parity Error Response bit) is set to 1.

pub const DEVSEL_MEDIUM_TIMING: Self

The read-only bit that represent the slowest time that a device will assert DEVSEL# for any bus command except Configuration Space read and writes.

If both DEVSEL_MEDIUM_TIMING and DEVSEL_SLOW_TIMING are not set, then it represents fast timing

pub const DEVSEL_SLOW_TIMING: Self

Check DEVSEL_MEDIUM_TIMING

pub const SIGNALED_TARGET_ABORT: Self

Sets to 1 when a target device terminates a transaction with Target- Abort.

pub const RECEIVED_TARGET_ABORT: Self

Sets to 1 by a master device when its transaction is terminated with Target-Abort

pub const RECEIVED_MASTER_ABORT: Self

Sets to 1 by a master device when its transaction (except for Special Cycle transactions) is terminated with Master-Abort.

pub const SIGNALED_SYSTEM_ERROR: Self

Sets to 1 when the device asserts SERR#

pub const DETECTED_PARITY_ERROR: Self

Sets to 1 when the device detects a parity error, even if parity error handling is disabled.

pub const fn empty() -> Self

Returns an empty set of flags.

pub const fn all() -> Self

Returns the set containing all flags.

pub const fn bits(&self) -> u16

Returns the raw value of the flags currently stored.

pub const fn from_bits(bits: u16) -> Option<Self>

Convert from underlying bit representation, unless that representation contains bits that do not correspond to a flag.

pub const fn from_bits_truncate(bits: u16) -> Self

Convert from underlying bit representation, dropping any bits that do not correspond to flags.

pub const unsafe fn from_bits_unchecked(bits: u16) -> Self

Convert from underlying bit representation, preserving all bits (even those not corresponding to a defined flag).

Safety

The caller of the bitflags! macro can chose to allow or disallow extra bits for their bitflags type.

The caller of from_bits_unchecked() has to ensure that all bits correspond to a defined flag or that extra bits are valid for this bitflags type.

pub const fn is_empty(&self) -> bool

Returns true if no flags are currently stored.

pub const fn is_all(&self) -> bool

Returns true if all flags are currently set.

pub const fn intersects(&self, other: Self) -> bool

Returns true if there are flags common to both self and other.

pub const fn contains(&self, other: Self) -> bool

Returns true if all of the flags in other are contained within self.

pub fn insert(&mut self, other: Self)

Inserts the specified flags in-place.

pub fn remove(&mut self, other: Self)

Removes the specified flags in-place.

pub fn toggle(&mut self, other: Self)

Toggles the specified flags in-place.

pub fn set(&mut self, other: Self, value: bool)

Inserts or removes the specified flags depending on the passed value.

pub const fn intersection(self, other: Self) -> Self

Returns the intersection between the flags in self and other.

Specifically, the returned set contains only the flags which are present in both self and other.

This is equivalent to using the & operator (e.g. ops::BitAnd), as in flags & other.

pub const fn union(self, other: Self) -> Self

Returns the union of between the flags in self and other.

Specifically, the returned set contains all flags which are present in either self or other, including any which are present in both (see Self::symmetric_difference if that is undesirable).

This is equivalent to using the | operator (e.g. ops::BitOr), as in flags | other.

pub const fn difference(self, other: Self) -> Self

Returns the difference between the flags in self and other.

Specifically, the returned set contains all flags present in self, except for the ones present in other.

It is also conceptually equivalent to the “bit-clear” operation: flags & !other (and this syntax is also supported).

This is equivalent to using the - operator (e.g. ops::Sub), as in flags - other.

pub const fn symmetric_difference(self, other: Self) -> Self

Returns the symmetric difference between the flags in self and other.

Specifically, the returned set contains the flags present which are present in self or other, but that are not present in both. Equivalently, it contains the flags present in exactly one of the sets self and other.

This is equivalent to using the ^ operator (e.g. ops::BitXor), as in flags ^ other.

pub const fn complement(self) -> Self

Returns the complement of this set of flags.

Specifically, the returned set contains all the flags which are not set in self, but which are allowed for this type.

Alternatively, it can be thought of as the set difference between Self::all() and self (e.g. Self::all() - self)

This is equivalent to using the ! operator (e.g. ops::Not), as in !flags.

Trait Implementations

impl Binary for Status

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl BitAnd for Status

fn bitand(self, other: Self) -> Self

Returns the intersection between the two sets of flags.

type Output = Status

The resulting type after applying the & operator.

impl BitAndAssign for Status

fn bitand_assign(&mut self, other: Self)

Disables all flags disabled in the set.

impl BitOr for Status

fn bitor(self, other: Status) -> Self

Returns the union of the two sets of flags.

type Output = Status

The resulting type after applying the | operator.

impl BitOrAssign for Status

fn bitor_assign(&mut self, other: Self)

Adds the set of flags.

impl BitXor for Status

fn bitxor(self, other: Self) -> Self

Returns the left flags, but with all the right flags toggled.

type Output = Status

The resulting type after applying the ^ operator.

impl BitXorAssign for Status

fn bitxor_assign(&mut self, other: Self)

Toggles the set of flags.

impl Clone for Status

fn clone(&self) -> Status

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Status

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Extend<Status> for Status

fn extend<T: IntoIterator<Item = Self>>(&mut self, iterator: T)

Extends a collection with the contents of an iterator.

fn extend_one(&mut self, item: A)

🔬This is a nightly-only experimental API. (extend_one)

Extends a collection with exactly one element.

fn extend_reserve(&mut self, additional: usize)

🔬This is a nightly-only experimental API. (extend_one)

Reserves capacity in a collection for the given number of additional elements.

impl FromIterator<Status> for Status

fn from_iter<T: IntoIterator<Item = Self>>(iterator: T) -> Self

Creates a value from an iterator.

impl Hash for Status

fn hash<__H: Hasher>(&self, state: &mut __H)

Feeds this value into the given Hasher.

fn hash_slice<H>(data: &[Self], state: &mut H)

where H: Hasher, Self: Sized,

Feeds a slice of this type into the given Hasher.

impl LowerHex for Status

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Not for Status

fn not(self) -> Self

Returns the complement of this set of flags.

type Output = Status

The resulting type after applying the ! operator.

impl Octal for Status

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Ord for Status

fn cmp(&self, other: &Status) -> Ordering

This method returns an Ordering between self and other.

fn max(self, other: Self) -> Self

where Self: Sized,

Compares and returns the maximum of two values.

fn min(self, other: Self) -> Self

where Self: Sized,

Compares and returns the minimum of two values.

fn clamp(self, min: Self, max: Self) -> Self

where Self: Sized,

Restrict a value to a certain interval.

impl PartialEq for Status

fn eq(&self, other: &Status) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl PartialOrd for Status

fn partial_cmp(&self, other: &Status) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

fn lt(&self, other: &Rhs) -> bool

Tests less than (for self and other) and is used by the < operator.

fn le(&self, other: &Rhs) -> bool

Tests less than or equal to (for self and other) and is used by the <= operator.

fn gt(&self, other: &Rhs) -> bool

Tests greater than (for self and other) and is used by the > operator.

fn ge(&self, other: &Rhs) -> bool

Tests greater than or equal to (for self and other) and is used by the >= operator.

impl Sub for Status

fn sub(self, other: Self) -> Self

Returns the set difference of the two sets of flags.

type Output = Status

The resulting type after applying the - operator.

impl SubAssign for Status

fn sub_assign(&mut self, other: Self)

Disables all flags enabled in the set.

impl UpperHex for Status

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Copy for Status

impl Eq for Status

impl StructuralPartialEq for Status